Date : Sun, 29 Mar 2009 23:29:56 +0100
From : jumbos.bazzar@... (Mark Haysman)
Subject: Master Compact Power Connections
Hi.
If you want to restore the original base unit, then I don't have the exact
spare, but if you want a modern replacement, then CPC PW01330 is as good as
any, cable plugs straight into a Compact. To power the drives as well,
probably best to use CPC PW01385, which has 4A output, rather than 2.4A -
presuming the Drive in the base unit uis happy with just 5v? If it needs 12v
too, I'll have some dual voltage adaptors in a week or so which will do the
job.
Mark.
----- Original Message -----
From: "Ian Wolstenholme" <bbcmailinglist@...>
To: <bbc-micro@...>
Sent: Sunday, March 29, 2009 11:04 PM
Subject: Re: [BBC-Micro] Master Compact Power Connections
Thank you, the multimeter confirms that the two pairs are top and
bottom like Rob said.
The curious thing is that the two leads from the internal PSU don't seem
to fit. They are a bit smaller than the mains ones, so I'm wondering now
if it's the power supply from the FileStore, and I swapped it with the
Compact
because the FileStore one wasn't working.
A quick check of my website confirms this! I must have cannibalised
the Compact drive box for more than the floppy drive, taking the PSU as
well, and for good measure, the lid!
Restoring the Master Compact is going to be a bit more involved than
I thought, and I've run out of weekend again! Anyone got a Master
Compact PSU going spare??!!
Best wishes,
Ian
----- Original Message -----
From: Phil Blundell [mailto:philb@...]
To: bbcmailinglist@...
Cc: bbc-micro@...
Sent: Sun, 29 Mar 2009 22:14:24 +0100
Subject: Re: [BBC-Micro] Master Compact Power Connections
On Sun, 2009-03-29 at 21:48 +0100, Ian Wolstenholme wrote:
> There are two sets of blue and brown leads and you can see one set of them
> in the first picture.
>
> What goes where, and what might happen if I do it wrong?
You can't really tell for sure by looking at the switch (unless it has
markings on that aren't shown in the photos). You really need to do
some tests with a multimeter to figure out which pins are which, Even
looking at another Compact is not necessarily a 100% guarantee since
your switch might be different for some reason (production change or
field repair for example).
Most likely, you want to connect the two brown leads to the top two
blades of the switch, and the two blue leads to the lower two blades on
the switch (or vice versa). However, it's best not to guess since doing
it wrong will mean that when you turn it on the switch will present a
dead short across the mains; this isn't likely to do you or your table
any real damage, but you might trip a circuit breaker in your fusebox
and the switch will very likely be destroyed by the experience.
Assuming you do have a multimeter on hand, proceed as follows:
1. Turn the switch off and verify that there is no continuity between
any two pins.
2. Now turn the switch on. You should find that the four pins now form
two pairs, with continuity between the two pins in each pair.
3. Connect the two blue wires to the pins from one pair, and the two
brown wires to the pins from another pair. In other words, when the
switch is on, you want the wires of the same colour to be connected
together. It doesn't matter which way round the wires go.
p.
_______________________________________________
bbc-micro mailing list
bbc-micro@...
http://lists.cloud9.co.uk/mailman/listinfo/bbc-micro
> _______________________________________________
> bbc-micro mailing list
> bbc-micro@...
> http://lists.cloud9.co.uk/mailman/listinfo/bbc-micro
>